This
product is not
compatible with
the Seidio Desktop Charging Cradle and Kit.
We are taking the
2-in-1 concept a step further with the cutting-edge design of
the Seidio CONVERT® Plus. An industry-first, the CONVERT® Plus features two
smartphone cases in one - a sleek case that includes a battery for everyday
protection and power and a heavy-duty case for the demands of the outdoors or
rugged professions.
Start with the Innocell Plus case
and upgrade by adding a layer of shock-absorbing silicone and a precision-fit
skeleton. On top of the protection offered by the case, your iPhone 4/4S will
remain secure thanks to our patented locking CONVERT® Plus holster that fits a
duty or utility belt up to 2” wide.
The
CONVERT® Plus Combo includes the Ultimate Screen Guard, Innocell Plus case, a
rugged skin and skeleton and the CONVERT® Plus
Holster.
Innocell Plus
case
- First iPhone 4/4S power case with a removable battery that is certified by Apple
- Sleek case (~ 0.73 cm) that
provides scratch protection without adding much bulk
- Case
includes a 1700mAh battery in a slot inside the case that allows users to swap
out battery with a spare
- Included micro-USB cable allows you to sync and charge your
iPhone 4/4S without the hassle of removing your
case
Rugged skin and
skeleton
- Controls, ports and camera are
covered for protection while remaining functional
-
Shock-absorption with less bulk
- Protects vulnerable parts of
device like corners and sides
CONVERT® Plus
Holster
- Face-in design protects face of
device
- Locks for security and swivels
for convenience
- Comfortably clips to belts up to
2” wide
Ultimate Screen
Guard
- Precision-cut
for each device
- Retains touch screen sensitivity
and clarity
- Installed without use of
adhesives
Q: How
do I turn the charging function on/off on the SURFACE™ Plus case?
A: When
your iPhone is in the SURFACE™™ Plus case containing the battery and the case
is not plugged into a power source (microUSB to USB, or microUSB to AC
adapter), you can charge your iPhone using the SURFACE™ Plus battery by
pressing the power button located on the bottom right corner of the SURFACE™
Plus case for 2-3 seconds until your iPhone detects the charging.
Once the
SURFACE™ Plus case has charged your iPhone to 100%, the charging will
automatically stop. However, if you would like to stop the SURFACE™ Plus case
from charging your iPhone before the iPhone battery reaches 100%, press the
power button again for 2-3 seconds until your iPhone detects that the charging
has stopped.
Q: How
is the SURFACE™ Plus bumper removed from the SURFACE™ Plus body?
A: On
the bottom side of the SURFACE™ Plus case, between the two speaker holes, there
is a thin rectangular slot/gap. Gently use your nails to gradually pry open the
gap between the bumper and SURFACE™ Plus body. If widening the middle gap does
not successfully detach the bumper, then continue increasing the gap towards a
speaker hole on either side to disengage the side tabs.
Should the
above instructions prove ineffective, then try gripping and pulling on the
speaker holes to pry the bumper away from the SURFACE™ Plus body.
Q: What
do blinking and fully lit charging lights on the SURFACE™ Plus case indicate?
A: There
are a total of 4 lights toward the bottom of the SURFACE™ Plus case. When the
case is not plugged to a power source and the power button is pressed, the
number of lights that turn on indicates how full the SURFACE™ Plus battery
inside the case is:
1 light
on indicates ~25% charged*
2 lights
on indicate ~50% charged
3 lights
on indicate ~75% charged
4 lights
on indicate ~100% charged
*Please
note: the only condition in which no light will turn on after the power button
has been pressed, is when the SURFACE™ Plus battery is completely drained.
When the
case is connected to a power source, the number of lights that are on and not
blinking indicates the levels of battery completely full, and the blinking
light indicates an incompletely filled level.
1
blinking light indicates 0-24% charged
1 light
on (non-blinking) + 1 blinking light indicates ~25% charged
2 lights
on (non-blinking) +1 blinking light indicates ~50% charged
3 lights
on (non-blinking) + 1 blinking light indicates ~75% charged
4 lights
on (non-blinking) indicates ~100% charged (This is only
possible when case is not connected to iPhone)
Q: In
what order will charging take place when the SURFACE™ Plus case is connected to
a power source?
A: When
the SURFACE™ Plus case containing the battery and your iPhone are connected to
a power source, the case is designed to automatically charge your iPhone to
full capacity first and then start charging the SURFACE™ Plus battery. Pressing
the power button will not affect the flow of charge from a power source.
Q: How
can I achieve optimal efficiency from my SURFACE™ Plus battery?
A: To
achieve optimal efficiency from your SURFACE™ Plus battery, start charging your
iPhone with the SURFACE™ Plus case when the iPhone battery level is around 60%.
The lower the iPhone battery level (less than 60%) at the start of charging,
the lower the operating efficiency of the SURFACE™ Plus battery.
Q: How do
I condition my SURFACE™ Plus battery?
A: Prior
to using your new Surface Plus battery, allow 8 hours for initial charge time.
Performance will increase after 5-6 full charges. In order to obtain full
capacity of the Surface Plus battery, it’s recommended that you leave the
battery charging for an additional 2-3 hours after the lights indicate it’s
fully charged (all 4 lights turn on when power button is pressed while case is
not connected to power source or iPhone). Drain the battery until only 1 light
turns on before charging again. That is one full cycle.
For use with Apple iPhone 4 (AT&T/Verizon/Unlocked)/Apple iPhone 4S (AT&T/Verizon/Sprint/Unlocked)
